When your water heater goes cold, one of the primary reasons might be an extinguished pilot light. Lighting the pilot light on your water heater is a straightforward task, but it’s important to approach it with care. In most cases, you’ll simply need to follow a series of steps to reignite the flame safely. This guide will provide you with clear instructions on how to light a pilot light on a water heater, ensuring you can restore hot water to your home without hassle.
Before diving into the process, it’s essential to understand the components involved and the safety precautions you should take. The pilot light is a small flame that ignites the gas burner in the water heater, allowing it to heat the water. If the pilot light has gone out, it could be due to a draft, a faulty thermocouple, or simply running out of gas. Regardless of the cause, knowing how to relight it can save you time and money. Let’s explore the steps involved in this process.
Understanding Your Water Heater’s Pilot Light System
Before attempting to light the pilot light, familiarize yourself with the components of your water heater’s ignition system. Most residential water heaters use either a standing pilot or an electronic ignition system. A standing pilot light is a small, continuously burning flame, while an electronic ignition system uses a spark to ignite the gas only when needed. The following sections will focus on lighting a standing pilot light, as this is the most common type found in older models.
Key components to be aware of include:
- Gas Control Valve: This valve controls the gas supply to the pilot light and burner. It typically has three settings: “Off,” “Pilot,” and “On.”
- Pilot Light Assembly: This is the small tube and nozzle where the pilot flame burns, often located near the bottom of the water heater.
- Thermocouple: This safety device detects whether the pilot light is lit. If it is not, it will shut off the gas supply to prevent leaks.
Safety Precautions Before Relighting
Before you start the process of lighting the pilot light, it’s crucial to prioritize safety. Here are some essential precautions to follow:
- Read the Manufacturer’s Instructions: Always refer to the water heater’s manual for specific instructions and safety warnings related to your model.
- Check for Gas Leaks: If you smell gas, do not attempt to light the pilot light. Immediately turn off the gas supply, ventilate the area, and contact your gas provider or a professional.
- Ventilation: Ensure the area around the water heater is well-ventilated to prevent gas accumulation.
- Wear Safety Gear: Consider wearing safety goggles and gloves to protect yourself from any potential hazards.
Tools and Materials Needed
Gather the following tools and materials to prepare for lighting the pilot light:
- Long lighter or match: A long lighter is safer for reaching the pilot light area.
- Flashlight: Useful for visibility in dimly lit areas.
- Wrench (if necessary): In case you need to tighten any fittings.
- Rags or paper towels: For cleaning any spills or checking for leaks.
Steps to Light the Pilot Light
Once you’ve ensured safety and gathered your materials, you can proceed with the following steps to light the pilot light:
1. Turn Off the Gas Supply
Locate the gas control valve on your water heater, typically found near the bottom. Turn the valve to the “Off” position and wait for at least five minutes to allow any accumulated gas to disperse.
2. Set the Valve to “Pilot”
After waiting, turn the gas control valve to the “Pilot” position. This setting allows gas to flow to the pilot light assembly without fully igniting the main burner.
3. Press the Reset Button
Most water heaters have a reset button located near the gas control valve. Press and hold this button. This action typically opens the gas line and allows gas to flow to the pilot light.
4. Light the Pilot Light
Using a long lighter or match, carefully ignite the pilot light while still holding the reset button. Ensure that the flame reaches the pilot light assembly. You may need to hold the lighter or match close enough to the pilot light while igniting it.
5. Continue Holding the Reset Button
After lighting the pilot light, continue to hold the reset button for about 30 seconds. This allows the thermocouple to heat up and confirm that the pilot light is functioning correctly. If the pilot light stays lit, you can release the reset button.
6. Turn the Gas Control Valve to “On”
With the pilot light successfully lit, turn the gas control valve from the “Pilot” position to the “On” position. This action allows gas to flow to the main burner, enabling your water heater to heat water properly.
7. Observe the Pilot Light
After igniting the pilot light and turning the control valve to “On,” observe the pilot flame for a few minutes. It should burn steadily and emit a blue flame. If you notice a yellow or orange flame or if the pilot light goes out again, you may need to troubleshoot further or consult a professional.
Troubleshooting Common Issues
If your pilot light fails to stay lit after following the steps above, there are a few common issues to consider:
- Dirty Pilot Orifice: Dust or debris can clog the pilot orifice, affecting the flame’s stability. Clean the orifice gently with a soft brush or compressed air.
- Faulty Thermocouple: If the thermocouple is malfunctioning, it may not detect the pilot flame correctly, leading to gas shut-off. A replacement may be necessary.
- Gas Supply Issues: Ensure that the gas supply is turned on and that there are no leaks or obstructions in the gas line.
Understanding these troubleshooting steps can save you time and help you maintain your water heater effectively. If you encounter persistent issues, it’s advisable to contact a licensed technician to assess the situation further.

Common Causes for a Pilot Light Going Out
Understanding why your pilot light may have extinguished is key to preventing future occurrences. Here are some of the most common causes:
- Drafts: Air currents from windows, doors, or ventilation can blow out the pilot flame. Ensure that there are no drafts in the vicinity of your water heater.
- Thermocouple Malfunction: A malfunctioning thermocouple can mistakenly shut off the gas supply, even if the pilot light is lit. Regular checks can help you identify issues before they become problematic.
- Gas Supply Interruption: If the gas supply is interrupted due to maintenance or supply issues, the pilot light will go out. Check with your gas provider if you suspect an interruption.
- Dirty Pilot Light Assembly: Dust and grime can accumulate in the pilot light assembly, affecting the flame quality. Regular cleaning can help maintain a steady pilot light.
- Old or Worn Components: Over time, components such as the thermocouple or gas control valve can wear out, leading to pilot light issues. Consider inspecting these parts if your pilot light frequently goes out.
Model-Specific Considerations for Lighting Pilot Lights
Different models of water heaters may have unique features or requirements for lighting the pilot light. Here are some considerations based on common types:
Conventional Gas Water Heaters
Most traditional gas water heaters with standing pilots will follow the process outlined in Part One. However, ensure that you are familiar with the specific layout of your model, as some may have additional safety features or slightly different controls.
High-Efficiency Water Heaters
High-efficiency models may utilize electronic ignition systems rather than standing pilot lights. These systems often require a different approach, usually involving a reset button and possibly a spark ignition. Refer to your owner’s manual for specific instructions.
Tankless Water Heaters
For tankless water heaters, the pilot light is often replaced by an ignition system that activates only when hot water is needed. If your tankless system is not producing hot water, check the ignition system and ensure that the gas supply is uninterrupted.
Propane vs. Natural Gas
Be aware of the type of gas your water heater uses. While the lighting process remains similar, propane systems may require adjustments in the gas control settings. Always ensure that your water heater is compatible with the type of gas supplied to your home.
Routine Maintenance to Prevent Pilot Light Issues
Regular maintenance can significantly reduce the chances of your pilot light going out. Here are some practical steps to incorporate into your routine:
- Regular Inspections: Check the pilot light and flame regularly. Look for any irregularities in the flame color or size, as these can indicate problems with the gas supply or pilot light assembly.
- Clean the Pilot Assembly: At least once a year, clean the pilot assembly to remove dust and debris. Use a soft brush or compressed air to clear any blockages, ensuring a strong and consistent flame.
- Inspect the Thermocouple: Periodically check the thermocouple for signs of wear or damage. If you notice any issues, consider replacing it to ensure that it functions correctly and safely.
- Check for Gas Leaks: Utilize soapy water to inspect joints and connections for gas leaks. Bubbles forming at the joints indicate a leak, which should be addressed immediately by a professional.
- Maintain Adequate Ventilation: Ensure that the area around your water heater is well-ventilated, preventing gas accumulation. This is particularly important in enclosed spaces.
Common Mistakes to Avoid When Lighting the Pilot Light
When attempting to light the pilot light, avoiding common mistakes is essential for safety and effectiveness. Here are some pitfalls to watch out for:
- Neglecting Safety Precautions: Always prioritize safety by ensuring proper ventilation and checking for gas leaks before lighting. Skipping these steps can lead to hazardous situations.
- Using Improper Tools: Avoid using short matches or lighters that can put your hand too close to the flame. Always use a long lighter to ignite the pilot safely.
- Forgetting to Hold the Reset Button: Failing to hold the reset button long enough after lighting the pilot can cause the gas to shut off prematurely. Ensure you hold it for at least 30 seconds.
- Ignoring Flame Color: A steady blue flame indicates a properly functioning pilot light, while a yellow or orange flame suggests an issue. Address any color irregularities promptly.
- Lighting the Pilot Light with a Gas Leak Present: Never attempt to light the pilot if you detect a gas smell. Turn off the gas, ventilate the area, and call a professional.
When to Call a Professional for Help
While many homeowners can successfully light their pilot light, there are situations when it’s best to call a professional. Consider reaching out for help if:
- You Smell Gas: If you detect a gas odor, do not attempt to light the pilot. Turn off the gas supply, evacuate the area, and contact your gas provider or a licensed technician immediately.
- Repeated Pilot Light Issues: If your pilot light continues to extinguish despite your efforts to light it, this may indicate a more significant problem within the system that requires professional diagnosis.
- Malfunctioning Thermocouple: If you suspect that the thermocouple is faulty and cannot replace it yourself, a technician can safely address the issue.
- Unusual Flames or Noises: If you observe abnormal flame behavior or hear unusual noises, it may indicate a gas flow issue or a malfunctioning component that needs professional inspection.
Understanding these aspects of your water heater’s pilot light system can empower you to maintain it effectively and address issues as they arise. Always prioritize safety and do not hesitate to seek professional assistance when needed.

Advanced Troubleshooting for Persistent Pilot Light Issues
Even after following the initial steps to light a pilot light on a water heater, you may encounter situations where the pilot light is difficult to keep lit. Understanding advanced troubleshooting methods can help you address these issues effectively.
1. Checking the Gas Supply Pressure
Low gas pressure can cause the pilot light to extinguish. If your water heater is part of a larger system, such as a home with multiple gas appliances, there may not be enough gas pressure at the heater. To check this, you may need a gas pressure gauge. Attach it to the gas line near the heater and check the pressure. If it’s below the manufacturer’s recommended levels, contact your gas supplier to address the issue. In some cases, a licensed technician may need to inspect your entire gas supply system for blockages or leaks.
2. Inspecting the Venting System
A blocked venting system can prevent proper airflow, leading to combustion issues that may extinguish the pilot light. Inspect the vent pipe for any signs of obstructions, such as bird nests, debris, or soot buildup. It’s crucial to ensure that the vent pipe is clear and allows for adequate exhaust of combustion gases. If you find any blockages, carefully remove them. If the venting appears damaged or corroded, consider hiring a professional to evaluate and repair it to ensure safety and compliance with local codes.
3. Evaluating the Flame Characteristics
The characteristics of the pilot flame can provide insights into underlying issues. A healthy pilot flame should be blue with a small inner cone and a larger outer cone. If the flame is yellow or orange, it may indicate incomplete combustion, potentially due to a dirty pilot orifice or a problem with the gas supply. Cleaning the pilot orifice with a soft brush can help, but if the problem persists, you may need to replace the pilot assembly. Always ensure safety by turning off the gas supply before performing any maintenance.
4. Checking for Electrical Issues in Electronic Ignition Systems
If your water heater features an electronic ignition system, electrical issues may prevent the pilot from lighting. Check the power supply to the water heater, ensuring that the circuit breaker hasn’t tripped. If the unit is plugged in and powered, inspect the ignition components, such as the igniter and wiring connections. If you notice any frayed wires or damaged components, these should be repaired or replaced by a professional to restore functionality.
5. Assessing the Age of Your Water Heater
Older water heaters may have components that have simply worn out over time. If your water heater is approaching the end of its expected lifespan (typically 10-15 years for traditional units), consider evaluating the overall condition of the unit. Frequent pilot light issues, along with other performance problems, may indicate that it’s time for a replacement. Investing in a new, efficient model can save you money on energy bills and reduce the risk of unexpected failures.
Preventive Measures to Maintain Your Water Heater
Taking proactive steps can help ensure your water heater functions optimally and the pilot light remains lit. Here are some preventive measures to incorporate into your home maintenance routine:
- Regular Professional Inspections: Schedule annual inspections with a licensed technician to assess the overall health of your water heater. They can identify potential issues before they become significant problems, ensuring that your system runs efficiently and safely.
- Flame Adjustment: If you notice that the pilot flame is too high or too low, it might need adjustment. This adjustment typically involves changing the gas flow through the control valve. However, this should be done by a professional to ensure safety and compliance with regulations.
- Insulate Pipes: Insulating the hot water pipes can help maintain water temperature, reducing the workload on your water heater. This not only enhances efficiency but can also minimize the frequency of the pilot light being activated, thereby extending the life of the components.
- Drain the Tank Regularly: Sediment buildup in the tank can lead to overheating and other issues that may affect the pilot light. Draining the tank every six months to a year can help remove sediment and ensure efficient operation.
Understanding the Role of Your Water Heater’s Anode Rod
The anode rod is a crucial component in your water heater that helps prevent corrosion. If the anode rod is depleted or malfunctioning, it can lead to rust and sediment buildup, potentially affecting the pilot light’s performance. Regularly inspecting and replacing the anode rod can extend the life of your water heater and help maintain overall efficiency. If you’re unsure how to do this, check out this guide on how to replace the anode rod in your water heater.
By understanding these advanced troubleshooting techniques and preventive measures, you can effectively manage pilot light issues and ensure the longevity of your water heater. Always prioritize safety and seek professional assistance when needed.
Successfully Maintain Your Water Heater and Keep the Pilot Light Lit
By following these comprehensive steps and understanding the intricacies of your water heater, you can confidently manage the pilot light and ensure a consistent supply of hot water. Regular maintenance and timely troubleshooting will not only keep your water heater functioning efficiently but also extend its lifespan. If you encounter persistent issues, don’t hesitate to reach out to a qualified technician for assistance. For additional maintenance tips, you can also check out how to drain a gas water heater.
1 thought on “How to Light a Pilot Light on a Water Heater (Step-by-Step Instructions)”